Ion Chromatography (IC-100PRO)

Product Description

Designed specifically for routine analysis that increases sample throughput.

Contamination-free with inert material throughout the fluidic flow path.

High performance from digital, thermally controlled conductivity detection.

For improved reproducibility, the heated and thermostatted high-performance conductivity detection cell permits measurements that are unaffected by temperature variations. This capability allows the instrument to provide sensitive conductivity results consistently, without variations in baseline drift. Advanced single-range digital output provides a full range for your ion analysis needs. Whether in low or high concentrations, ions of interest are easily identified in this detection range.

IC-100PRO adopts complete polymeric systems constructed of PEEK materials. Metal-free materials prevent the acid and base mobile phases traditionally used in IC analysis from contaminating and corroding the system. The PEEK material used provides a chemically inert pump and system flow path compatible with aqueous eluents of pH 0-14. Maintaining your system is simplified with materials that do not promote problems in the system. You can expect lower maintenance cost with the use of factory-equipped piston seal wash. This standard feature protects the dual-piston pumping system between routine maintenance cycles by rinsing the pistons and rear seals continuously with DI water. The PEEK tubing used to plumb the system is easy to use and cut for fast replacement or plumbing flexibility. The IC-100PRO are configured and ready for your most challenging anion or cation analysis.

For improved reproducibility, the heated and thermostatted high-performance conductivity detection cell permits measurements that are unaffected by temperature variations. This capability allows the instrument to provide sensitive conductivity results consistently, without variations in baseline drift. Advanced single-range digital output provides a full range for your ion analysis needs. Whether in low or high concentrations, ions of interest are easily identified in this detection range.

Type	Serial dual-reciprocating pistons, microprocessor-controlled constant stroke, variable speed
Construction	Chemically inert, metal-free PEEK pump heads and flow paths compatible with aqueous eluents of pH 0–14 and reversed-phase solvents
Control mode	Full control through front panel
Maximum operating pressure	45 MPa
Pressure ripple	<1.0 % from 0.4 to 2.0 mL/min at 1000–3000 psi
Flow rate range	0.01–9.99 mL/min in 0.01 increments, typical operating range is 0.4–2.0 mL/min
Flow precision	± 0.1 %
Flow accuracy	± 0.05 %
System Flow Constancy	Typically < 0.1 %
Piston seal wash	Dual-pump head, wash can be continuous when connected to rinse solution supply
Pressure alarm limits	Upper limit 0–45 MPa or 0–6400 psi in one unit (MPa or psi) increments, lower limit can be set up to one unit lower than upper limit

2. Conductivity Detector

Type	Microprocessor-controlled digital signal processor
Cell drive	8-kHz square wave
Linearity	1% at 1 ms
Resolution	0.1 ns
Full-scale output ranges	Digital signal range: 0–15,000 µs Analog signal range: 0–15,000 µs
Electronic noise	±0.1 ns when background conductivity is 0–150 µs ±2 ns when background conductivity is 151–3200 µs
Filter	Rise times from 0 to 10 s, user selectable
Temperature compensation	Fixed at 1.7% per 1 ºC at cell temperature
Temperature range	Ambient +7 ºC to 55 ºC
Temperature stability	< 0.01 ºC
Cell electrodes	Passivated 316 stainless steel
Cell body	Chemically inert polymeric material
Cell volume	<1.4 µL
Heat exchanger	Low dispersion
Maximum cell operating pressure	2 MPa (300 psi)
Suppressor control	Self-Regenerating electrolytic Suppressor AES, 0–150 mA in 1-mA increments SRS, 0–500 mA in 1-mA increments
Separating capacity	Analyze F - , Cl - , NO 2 - , PO 4 3- , Br - , NO 3 - , SO 4 2- , ClO 2 - , ClO 3 - , BrO 3 - in 16 minutes. Analyze Li + , Na + , NH 4 + , K + , Mg 2+ , Ca 2+ , Sr 2+ , Ba 2+ in 20 minutes.
Lower limits of detection	<0.1ug/L (CI - ), 3ug/L (Na + )
Linear limits	> 10 3
Linear correlation coefficient	> 0.995
RSD%	< 1.5% (measured by SO 4 2- )

3. Column

AN serial ion exchange column
Alltech serial ion exchange column

4. Workstation

Input range: -1.3V--+1.3V
Sensitivity: 0.05uV.S
Frequency: 6000

5. Physical Specifications

Display	Large touch-sensitive LCD display
Power requirements	220V±10% 50Hz / 110V±10% 60Hz
Operating temperature	15–30 ºC
Operating humidity range	5–85% relative, noncondensing
Control mode	Full control through front panel
Communication protocol	RS232-USB port
Dimensions (h × w × d)	56.1 × 22.4 × 53.3 cm (22.1 × 8.8 × 21 in.)
Weight	24.5 kg (54 lb)

Packing List for IC-100PRO Ion Chromatography

NO.	Name	Type	Unit	Quantity
1	Main processor	IC-100		1
2	O type sealing washer	Φ4.5×1.5		30
3	Simulated conductance board			1
4	Conical column tie-in			4
5	Four fluorin pipeline	Φ1.5	Meter	3
6	Electric iron	20W		2
7	Flanging tip			2
8	Injector	2ml		10
9	Syringe needle			10
10	Blown fuse	2A		10
11	Lever	100×12		1
12	Blade	One-edged		2
13	Long nosed pliers	150mm		1
14	Screwdriver			1
15	Power cord			2
16	Instruction manual			1
17	Flow pipeline joint	M6		8
18	Inhibitor	Self-regenerate		1
19	Anion chromatographic column			1
20	Chromatography working station	Including disk, signal line, manual	Set	1
21	Certificate of quality			1
22	Constant loaded resistance	100Ω		5
23	Pump accessories		Bag	1

Trademark:	Neutral English
Model NO.:	IC-100PRO
Productivity:	1, 000pcs/year
Unit Price/Payment:	FOB USD23, 500.00/pc
Origin:	Tsingtao
Packing:	Carton or boarding ark
Min. Order:	1
Transportation:	By air or by sea
Company:	Tsingtao Unicom-Optics Instruments Co., Ltd.